A fireplace blower is a type of venting system that works to draw air from the room through your chimney. The process helps remove smoke and heat more quickly than it would otherwise, which can reduce wear on your chimney lining by up to 50%. It also allows you to use less wood for fuel, saving money in the long run. If you are looking for an easy way to install a fireplace blower into your home’s existing fire place then this guide will help!
Installing a fireplace blower is not an easy task, but it can be done by following these steps. First, you must unpack the blower and remove the front cover. Next, attach the fan to its mounting bracket using four screws. Now pull out your electrical cord from inside of your wall or partition and plug it in to an outlet that has been covered with a GFCI-protected receptacle box. After that, turn on your power switch for 120 volts AC at 60 Hz which will be located on the back of your unit. Finally, set up temperature controls by turning them all up or down until you reach desired room temperature!
Purpose of a Fireplace Blower
A fireplace blower’s purpose is to circulate heat from the fire throughout the room. This will help keep you warm and make your fireplace more efficient.
If you are considering installing a fireplace blower, there are a few things you should know before purchasing one. In this article, we will discuss the different types of fireplace blowers, how to choose the right one for your fireplace, and how to install it.
Types of Fireplace Blowers
There are three types of fireplace blowers: direct-vent, in-line, and out-of-line. Direct-vent blowers attach directly to the vent pipe, while in-line blowers attach to the outside of your home, and out-of-line blowers are installed on the inside.
The type you need will depend on where your fireplace is situated in relation to your home. If it’s near an exterior wall, a direct-vent blower would be best because it attaches directly into that vent pipe. If your fireplace is in the middle of your home, an in-line blower would work best because it can attach to the outside wall. And if your fireplace is in a room that doesn’t have an exterior wall (like a finished basement), you will need an out-of-line blower.
Each type of blower has its own advantages and disadvantages. For example, direct-vent blowers are easy to install because they attach directly into the vent pipe; however, if you’re installing them on an exterior wall, it can be difficult to run all of your wiring outside without causing damage to your house.
On the other hand, in-line blowers are easy to install because you can attach them directly outside. However, if your fireplace is near an exterior wall or in the middle of your home, it will need a direct-vent blower instead.
An out-of-line blower is usually best for finished basements with no windows nearby. These types of blowers are also the least expensive, but they can take up space in your home and will be more difficult to install than an in-line or direct-vent blower.
Once you decide which type of fireplace blower is right for you, it’s time to choose one that fits your needs perfectly! There are several factors to consider, including the BTU rating (how much heat it can circulate), power source (electric or gas-powered), and noise level.
The size of your room is also important – you want to make sure that blower will sufficiently warm up your space without being too powerful for the area. For example, if you have a large room with high ceilings, you will need a blower with a higher BTU rating than if you have a small room with low ceilings.
Finally, consider the noise level of the blower before purchasing it. If you don’t want a loud machine running all day and night, make sure to choose one that is relatively quiet.
How to install a Fireplace Blower?
The fireplace blower is the device that blows air into your fire, using this energy to increase its flame. You can use it for gas or wood burning fires.
There are different models of these devices depending on what type of fuel you want to burn and where you live (there are also indoor and outdoor options). For example, if you live in a cold place where the temperature outside drops below zero you’ll need an “indoor/outdoor” fireplace blower, which can handle high and low temperatures. You won’t find this information on your product manual – it comes from customer reviews online.
This article will discuss some of the details for how to install a fireplace blower. The first step is to identify the type of blower you need and the manufacturer’s specifications. Once you have this information, you can purchase the correct blower and begin the installation process.
The general steps for how to install a fireplace blower are as follows:
- Locate your fireplace and remove the old blower.
- Attach the new fireplace blower with screws or bolts, checking that it’s secure and in good condition (i.e., no cracks).
- Connect the wires to your electrical system according to manufacturer specifications for this particular type of device. The last step is simply turning on power when you are ready to use your fireplace blower.
- Now that you know how to install a fireplace blower, it’s time to get started! Remember to consult your product manual and manufacturer specifications before beginning the installation process. Once you have all of the necessary information, you can purchase the correct blower and start enjoying its benefits in no time at all.
If you have any questions about this process, feel free to leave a comment below. We’d be happy to help!
What you will need for installation a Fireplace Blower?
- Screwdriver Set (standard and Phillips/flat head)
- Tapping Screws (or Self-Tapping screws)
- Level
- Tape Measure
- Saw Horses/Work Bench.
Once you have gathered your installation supplies, you can begin the installation process. The first step is to remove the damper cover plate on the fireplace. This is usually located on the front of the fireplace, and is held in place with screws. Remove the screws and set the cover plate aside.
Next, you will need to remove the old blower housing. This is typically attached to the fireplace with screws or bolts. Once it has been removed, you can discard it. Now that the old blower housing has been removed, you can install the new one.
Attach the new blower housing to the fireplace with screws or bolts, making sure that it is level. Once it is attached, you can reattach the damper cover plate using the screws that were removed earlier.
Now it is time to install the blower unit itself. This will typically be attached to the back of the blower housing with just a few screws. Once it has been attached, use your level to ensure that it is even all around.
Finally, you need to attach the wiring harness from the new blower unit to existing wires in your home’s junction box. This will also require some basic electrical knowledge and skill. Once the wiring is complete, you can reattach the fireplace’s front panel and you are done!
Now that your fireplace blower is installed, it is time to test it out. Turn on your fireplace and enjoy the added warmth and comfort that comes with a working blower unit. If there are any problems with the installation, be sure to consult your installation guide or contact a professional contractor.
Now that you know how to install a fireplace blower, you can add this simple upgrade to your home and enjoy the benefits it provides. Not only will you stay warm and comfortable all winter long, but you will also improve the efficiency of your fireplace.
Step-by-step instructions on how to install a Fireplace Blower
- Locate the blower on the fireplace and remove any screws or bolts that are holding it in place
- Plug the cord of the blower into an outlet and insert the plug into the wall
- Attach the flue pipe to the top of the blower using either screws or clamps
- If you have a damper, open it and slide the blower into the fireplace
- Close the damper
- Turn on the blower by flipping the switch on the cord
- Enjoy your warm fire!
If you have any questions about installing a Fireplace Blower, please don’t hesitate to ask. Our experts are more than happy to help. And be sure to check out our other fireplace installation guides for more tips and tricks. Thanks for reading!
Troubleshooting tips and FAQs
- If the blower does not turn on, make sure that it is plugged into a working electrical outlet.
- The fireplace opening should be at least 16″ x 20″. Anything smaller will cause problems with air flow and power outlets may need to be moved for optimal performance.
- Make sure that the blower is in the correct position according to your fireplace. The intake and exhaust should be pointing in the right direction.
- If you are using a gas fireplace, make sure that the blower is turned off when the fireplace is lit. Blowing air on an open flame could create a dangerous situation.
- If the blower is making strange noises, it may be a sign that there is something wrong with it. In this case, you should stop using it and contact the manufacturer for help.
Environmental Protection and Safety
When you install a fireplace blower, it is important to protect the environment and your safety. Follow these steps: Choose an appropriate location that has enough space for installation and ventilation; if possible, choose a place with good drainage so water won’t seep in when it rains. Make sure there are no obstacles blocking airflow.
Connect the blower to an electrical outlet and the fireplace. Follow the manufacturer’s instructions for connecting the wires. Test the blower by turning it on; if it is not working, check all of the connections.
Make sure there is plenty of clearance around the top and sides of the fireplace opening. The flue and chimney should also be clear.
Install the blower according to the manufacturer’s instructions. Most blowers come with a bracket that attaches to the fireplace wall; make sure it is securely attached so it doesn’t fall off.
The blower will create an updraft that pulls air into the fireplace and up the chimney. The flue should be opened during the entire first hour of operation to avoid smoke leakage.
Safety Tips
When installing your fireplace blower, please keep the following safety tips in mind:
- Always read and follow the manufacturer’s instructions.
- Never operate a fireplace blower without proper clearance to combustibles.
- Make sure that the power supply is adequate for your blower before installation.
- Be sure to use the right tool for installation.
- Never install a fireplace blower in wet conditions or near water.
FAQs
How do I know if my fireplace needs a blower?
The best way to tell is to look at your fireplace. If the front of your fireplace has an opening that’s larger than the back, then you need a blower. Additionally, fireplaces with glass doors typically require blowers in order to circulate the heat.
What are the benefits of having a fireplace blower?
There are several benefits to having a fireplace blower. First, it can help increase the heat output of your fireplace by up to 30%. Second, it helps circulate the air in the room, which can make you feel warmer. And finally, it helps keep the glass doors of your fireplace clean.
How do I know if my fireplace needs a fan?
The best way to tell is to look at your fireplace. If the front of your fireplace has an opening that’s larger than the back, then you need a fan. Additionally, fireplaces with glass doors typically require fans in order to circulate the heat.
What are the benefits of having a fireplace blower?
There are several benefits to having a fireplace blower. First, it can help increase the heat output of your fireplace by up to 30%. Second, it helps circulate the air in the room, which can make you feel warmer. And finally, it helps keep the glass doors of your fireplace clean.
Conclusion
Now that you know how to install a fireplace blower, get out there and do it! It’s a relatively easy process, and the results are definitely worth it. Not only will your fireplace be more efficient, but it will also be safer and more comfortable to use. So don’t wait – start shopping for a fireplace blower today.